i2M audio is NOISY
i2M audio is NOISY
When hooking my guitar up to my MacBook Pro's audio input, the audio is clean, even when running through amp simulations. When I use the i2M's audio, it's very very noisy and I cannot figure out why.
My "Band": Chosen Blood
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Re: i2M audio is NOISY
How noisy is it? Is it only noticeable using amp-sims, or all the time?
What does the noise sound like, is it white or a hum?
What does the noise sound like, is it white or a hum?
Re: i2M audio is NOISY
White/pink noise. It's noticeable all the time, but the amps really amplify it.
My "Band": Chosen Blood
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Re: i2M audio is NOISY
There will be some noise. The input has a very high impedance which does produce more noise than a low-impedance input. Also, the converter is 16-bit, so it won't be as quiet as a 24-bit converter.
The question is whether it is higher than it should be...
What's the gain is set on the i2M's preamp? Does the noise reduce as the gain is reduced?
The question is whether it is higher than it should be...
What's the gain is set on the i2M's preamp? Does the noise reduce as the gain is reduced?
Re: i2M audio is NOISY
Have you tried rebooting the Mac? I've had noise problems and this has always solved the problem. Also only open the applications you need.
Good luck!
Good luck!
Re: i2M audio is NOISY
Setting the preamp gain to -12dB had little effect. I've also tried rebooting, etc
Last edited by prometh on Thu Aug 16, 2012 4:26 pm, edited 2 times in total.
My "Band": Chosen Blood
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Re: i2M audio is NOISY
It sounds like the i2M may have developed a fault.
Is it possible to record some audio to let us have a look to confirm this?
Does the i2M show any other problems?
Is it possible to record some audio to let us have a look to confirm this?
Does the i2M show any other problems?
Re: i2M audio is NOISY
I just tried my laptop's input again and it's noisy too, but not as noisy. I guess my guitar is noisy and my Axe-Fx II must really be cleaning it up.
My "Band": Chosen Blood
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Instruments: BC Rich Warlock, Ibanez SR300, Washburn D10S
Signal Path: Instrument → Grace m101 → Axe-Fx II → Stewart World 1.2 → Atomic Reactor FRs
Other Equipment: MacBook Pro, Furman PF-Pro R, Yamaha HS50M
Re: i2M audio is NOISY
Try with a different guitar/lead, or with a different input entirely, like a microphone, synth or whatever you have.
Re: i2M audio is NOISY
I am getting the high frequency disturbance that is mentioned here as the line input issue,but that's far less difficult right now than the more noticeable noise..